+REGULATION (EU) 2023/1542 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 12 July 2023 concerning batteries and waste batteries, amending Directive 2008/98/EC and Regulation (EU) 2019/1020 and repealing Directive 2006/66/EC (Text with EEA relevance)
---+CHAPTER I General provisions
------+Article 1 Subject matter and scope
---------+Article 1 1.
---------+Article 1 2.
---------+Article 1 3.
---------+Article 1 4.
---------+Article 1 5.
---------+Article 1 6.
------+Article 2 Objectives
------+Article 3 Definitions
---------+Article 3 1.
---------+Article 3 2.
------+Article 4 Free movement
---------+Article 4 1.
---------+Article 4 2.
------+Article 5 Sustainability, safety, labelling and information requirements for batteries
---------+Article 5 1.
---------+Article 5 2.
---+CHAPTER II Sustainability and safety requirements
------+Article 6 Restrictions on substances
---------+Article 6 1.
---------+Article 6 2.
---------+Article 6 3.
---------+Article 6 4.
---------+Article 6 5.
------+Article 7 Carbon footprint of electric vehicle batteries, rechargeable industrial batteries and LMT batteries
---------+Article 7 1.
---------+Article 7 2.
---------+Article 7 3.
---------+Article 7 4.
---------+Article 7 5.
------+Article 8 Recycled content in industrial batteries, electric vehicle batteries, LMT batteries and SLI batteries
---------+Article 8 1.
---------+Article 8 2.
---------+Article 8 3.
---------+Article 8 4.
---------+Article 8 5.
---------+Article 8 6.
------+Article 9 Performance and durability requirements for portable batteries of general use
---------+Article 9 1.
---------+Article 9 2.
---------+Article 9 3.
------+Article 10 Performance and durability requirements for rechargeable industrial batteries, LMT batteries and electric vehicle batteries
---------+Article 10 1.
---------+Article 10 2.
---------+Article 10 3.
---------+Article 10 4.
---------+Article 10 5.
---------+Article 10 6.
------+Article 11 Removability and replaceability of portable batteries and LMT batteries
---------+Article 11 1.
---------+Article 11 2.
---------+Article 11 3.
---------+Article 11 4.
---------+Article 11 5.
---------+Article 11 6.
---------+Article 11 7.
---------+Article 11 8.
---------+Article 11 9.
------+Article 12 Safety of stationary battery energy storage systems
---------+Article 12 1.
---------+Article 12 2.
---------+Article 12 3.
---+CHAPTER III Labelling, marking and information requirements
------+Article 13 Labelling and marking of batteries
---------+Article 13 1.
---------+Article 13 2.
---------+Article 13 3.
---------+Article 13 4.
---------+Article 13 5.
---------+Article 13 6.
---------+Article 13 7.
---------+Article 13 8.
---------+Article 13 9.
---------+Article 13 10.
------+Article 14 Information on the state of health and expected lifetime of batteries
---------+Article 14 1.
---------+Article 14 2.
---------+Article 14 3.
---------+Article 14 4.
---------+Article 14 5.
---+CHAPTER IV Conformity of batteries
------+Article 15 Presumption of conformity of batteries
---------+Article 15 1.
---------+Article 15 2.
---------+Article 15 3.
------+Article 16 Common specifications
---------+Article 16 1.
---------+Article 16 2.
---------+Article 16 3.
------+Article 17 Conformity assessment procedures
---------+Article 17 1.
---------+Article 17 2.
---------+Article 17 3.
---------+Article 17 4.
------+Article 18 EU declaration of conformity
---------+Article 18 1.
---------+Article 18 2.
---------+Article 18 3.
---------+Article 18 4.
---------+Article 18 5.
------+Article 19 General principles of the CE marking
------+Article 20 Rules and conditions for affixing the CE marking
---------+Article 20 1.
---------+Article 20 2.
---------+Article 20 3.
---------+Article 20 4.
---------+Article 20 5.
---+CHAPTER V Notification of conformity assessment bodies
------+Article 21 Notification
------+Article 22 Notifying authorities
---------+Article 22 1.
---------+Article 22 2.
---------+Article 22 3.
---------+Article 22 4.
------+Article 23 Requirements relating to notifying authorities
---------+Article 23 1.
---------+Article 23 2.
---------+Article 23 3.
---------+Article 23 4.
---------+Article 23 5.
---------+Article 23 6.
------+Article 24 Information obligation on notifying authorities
------+Article 25 Requirements relating to notified bodies
---------+Article 25 1.
---------+Article 25 2.
---------+Article 25 3.
---------+Article 25 4.
---------+Article 25 5.
---------+Article 25 6.
---------+Article 25 7.
---------+Article 25 8.
---------+Article 25 9.
---------+Article 25 10.
---------+Article 25 11.
------+Article 26 Presumption of conformity of notified bodies
------+Article 27 Subsidiaries of and subcontracting by notified bodies
---------+Article 27 1.
---------+Article 27 2.
---------+Article 27 3.
---------+Article 27 4.
------+Article 28 Application for notification
---------+Article 28 1.
---------+Article 28 2.
---------+Article 28 3.
------+Article 29 Notification procedure
---------+Article 29 1.
---------+Article 29 2.
---------+Article 29 3.
---------+Article 29 4.
---------+Article 29 5.
---------+Article 29 6.
------+Article 30 Identification numbers and lists of notified bodies
---------+Article 30 1.
---------+Article 30 2.
------+Article 31 Changes to notifications
---------+Article 31 1.
---------+Article 31 2.
------+Article 32 Challenge to the competence of notified bodies
---------+Article 32 1.
---------+Article 32 2.
---------+Article 32 3.
---------+Article 32 4.
------+Article 33 Operational obligations of notified bodies
---------+Article 33 1.
---------+Article 33 2.
---------+Article 33 3.
---------+Article 33 4.
---------+Article 33 5.
------+Article 34 Appeal against decisions of notified bodies
------+Article 35 Information obligation on notified bodies
---------+Article 35 1.
---------+Article 35 2.
------+Article 36 Exchange of experience and good practice
------+Article 37 Coordination of notified bodies
---+CHAPTER VI Obligations of economic operators other than the obligations in Chapters VII and VIII
------+Article 38 Obligations of manufacturers
---------+Article 38 1.
---------+Article 38 2.
---------+Article 38 3.
---------+Article 38 4.
---------+Article 38 5.
---------+Article 38 6.
---------+Article 38 7.
---------+Article 38 8.
---------+Article 38 9.
---------+Article 38 10.
---------+Article 38 11.
------+Article 39 Obligations of suppliers of battery cells and battery modules
------+Article 40 Obligations of authorised representatives
---------+Article 40 1.
---------+Article 40 2.
---------+Article 40 3.
---------+Article 40 4.
------+Article 41 Obligations of importers
---------+Article 41 1.
---------+Article 41 2.
---------+Article 41 3.
---------+Article 41 4.
---------+Article 41 5.
---------+Article 41 6.
---------+Article 41 7.
---------+Article 41 8.
------+Article 42 Obligations of distributors
---------+Article 42 1.
---------+Article 42 2.
---------+Article 42 3.
---------+Article 42 4.
---------+Article 42 5.
---------+Article 42 6.
------+Article 43 Obligations of fulfilment service providers
------+Article 44 Case in which obligations of manufacturers apply to importers and distributors
------+Article 45 Obligations of economic operators placing on the market or putting into service batteries that have been subject to preparation for re-use, preparation for repurposing, repurposing or remanufacturing
---------+Article 45 1.
---------+Article 45 2.
------+Article 46 Identification of economic operators
---------+Article 46 1.
---------+Article 46 2.
---+CHAPTER VII Obligations of economic operators as regards battery due diligence policies
------+Article 47 Scope of this Chapter
------+Article 48 Battery due diligence policies
---------+Article 48 1.
---------+Article 48 2.
---------+Article 48 3.
---------+Article 48 4.
---------+Article 48 5.
---------+Article 48 6.
---------+Article 48 7.
---------+Article 48 8.
------+Article 49 Economic operator’s management system
---------+Article 49 1.
---------+Article 49 2.
------+Article 50 Risk management obligations
---------+Article 50 1.
---------+Article 50 2.
---------+Article 50 3.
---------+Article 50 4.
------+Article 51 Third-party verification of battery due diligence policies
---------+Article 51 1.
---------+Article 51 2.
------+Article 52 Disclosure of information on battery due diligence policies
---------+Article 52 1.
---------+Article 52 2.
---------+Article 52 3.
---------+Article 52 4.
------+Article 53 Recognition of due diligence schemes
---------+Article 53 1.
---------+Article 53 2.
---------+Article 53 3.
---------+Article 53 4.
---------+Article 53 5.
---------+Article 53 6.
---------+Article 53 7.
---------+Article 53 8.
---+CHAPTER VIII Management of waste batteries
------+Article 54 Competent authority
---------+Article 54 1.
---------+Article 54 2.
---------+Article 54 3.
---------+Article 54 4.
------+Article 55 Register of producers
---------+Article 55 1.
---------+Article 55 2.
---------+Article 55 3.
---------+Article 55 4.
---------+Article 55 5.
---------+Article 55 6.
---------+Article 55 7.
---------+Article 55 8.
---------+Article 55 9.
---------+Article 55 10.
---------+Article 55 11.
---------+Article 55 12.
---------+Article 55 13.
------+Article 56 Extended Producer Responsibility
---------+Article 56 1.
---------+Article 56 2.
---------+Article 56 3.
---------+Article 56 4.
---------+Article 56 5.
------+Article 57 Producer Responsibility Organisation
---------+Article 57 1.
---------+Article 57 2.
---------+Article 57 3.
---------+Article 57 4.
---------+Article 57 5.
---------+Article 57 6.
---------+Article 57 7.
---------+Article 57 8.
------+Article 58 Authorisation on fulfilment of extended producer responsibility
---------+Article 58 1.
---------+Article 58 2.
---------+Article 58 3.
---------+Article 58 4.
---------+Article 58 5.
---------+Article 58 6.
---------+Article 58 7.
------+Article 59 Collection of waste portable batteries
---------+Article 59 1.
---------+Article 59 2.
---------+Article 59 3.
---------+Article 59 4.
---------+Article 59 5.
---------+Article 59 6.
---------+Article 59 7.
------+Article 60 Collection of waste LMT batteries
---------+Article 60 1.
---------+Article 60 2.
---------+Article 60 3.
---------+Article 60 4.
---------+Article 60 5.
---------+Article 60 6.
---------+Article 60 7.
---------+Article 60 8.
------+Article 61 Collection of waste SLI batteries, waste industrial batteries and waste electric vehicle batteries
---------+Article 61 1.
---------+Article 61 2.
---------+Article 61 3.
---------+Article 61 4.
------+Article 62 Obligations of distributors
---------+Article 62 1.
---------+Article 62 2.
---------+Article 62 3.
---------+Article 62 4.
---------+Article 62 5.
---------+Article 62 6.
------+Article 63 Deposit return systems for batteries
------+Article 64 Obligations of end-users
---------+Article 64 1.
---------+Article 64 2.
------+Article 65 Obligations of operators of treatment facilities
---------+Article 65 1.
---------+Article 65 2.
------+Article 66 Participation of public waste management authorities
---------+Article 66 1.
---------+Article 66 2.
------+Article 67 Participation of voluntary collection points
---------+Article 67 1.
---------+Article 67 2.
------+Article 68 Restrictions regarding handover of waste portable batteries and waste LMT batteries
---------+Article 68 1.
---------+Article 68 2.
------+Article 69 Obligations for Member States regarding collection targets for waste portable batteries and waste LMT batteries
---------+Article 69 1.
---------+Article 69 2.
---------+Article 69 3.
---------+Article 69 4.
---------+Article 69 5.
------+Article 70 Treatment
---------+Article 70 1.
---------+Article 70 2.
---------+Article 70 3.
---------+Article 70 4.
---------+Article 70 5.
------+Article 71 Targets for recycling efficiency and recovery of materials
---------+Article 71 1.
---------+Article 71 2.
---------+Article 71 3.
---------+Article 71 4.
---------+Article 71 5.
---------+Article 71 6.
------+Article 72 Shipment of waste batteries
---------+Article 72 1.
---------+Article 72 2.
---------+Article 72 3.
---------+Article 72 4.
------+Article 73 Preparation for re-use or preparation for repurposing of waste LMT batteries, waste industrial batteries and waste electric vehicle batteries
---------+Article 73 1.
---------+Article 73 2.
---------+Article 73 3.
---------+Article 73 4.
------+Article 74 Information on prevention and management of waste batteries
---------+Article 74 1.
---------+Article 74 2.
---------+Article 74 3.
---------+Article 74 4.
---------+Article 74 5.
---------+Article 74 6.
---------+Article 74 7.
------+Article 75 Minimum requirements for reporting to the competent authorities
---------+Article 75 1.
---------+Article 75 2.
---------+Article 75 3.
---------+Article 75 4.
---------+Article 75 5.
---------+Article 75 6.
---------+Article 75 7.
---------+Article 75 8.
---------+Article 75 9.
------+Article 76 Reporting to the Commission
---------+Article 76 1.
---------+Article 76 2.
---------+Article 76 3.
---------+Article 76 4.
---------+Article 76 5.
---+CHAPTER IX Digital battery passport
------+Article 77 Battery passport
---------+Article 77 1.
---------+Article 77 2.
---------+Article 77 3.
---------+Article 77 4.
---------+Article 77 5.
---------+Article 77 6.
---------+Article 77 7.
---------+Article 77 8.
---------+Article 77 9.
---------+Article 77 10.
------+Article 78 Technical design and operation of the battery passport
---+CHAPTER X Union market surveillance and Union safeguard procedures
------+Article 79 Procedure at national level for dealing with batteries presenting a risk
---------+Article 79 1.
---------+Article 79 2.
---------+Article 79 3.
---------+Article 79 4.
---------+Article 79 5.
---------+Article 79 6.
---------+Article 79 7.
---------+Article 79 8.
------+Article 80 Union safeguard procedure
---------+Article 80 1.
---------+Article 80 2.
---------+Article 80 3.
---------+Article 80 4.
------+Article 81 Compliant batteries which present a risk
---------+Article 81 1.
---------+Article 81 2.
---------+Article 81 3.
---------+Article 81 4.
---------+Article 81 5.
---------+Article 81 6.
------+Article 82 Joint activities
------+Article 83 Formal non-compliance
---------+Article 83 1.
---------+Article 83 2.
------+Article 84 Non-compliance with due diligence obligations
---------+Article 84 1.
---------+Article 84 2.
---+CHAPTER XI Green public procurement and procedure for amending restrictions on substances
------+Article 85 Green public procurement
---------+Article 85 1.
---------+Article 85 2.
---------+Article 85 3.
------+Article 86 Restriction procedure for substances
---------+Article 86 1.
---------+Article 86 2.
---------+Article 86 3.
---------+Article 86 4.
---------+Article 86 5.
---------+Article 86 6.
---------+Article 86 7.
---------+Article 86 8.
---------+Article 86 9.
---------+Article 86 10.
---------+Article 86 11.
------+Article 87 Opinion of the Agency’s Committees
---------+Article 87 1.
---------+Article 87 2.
---------+Article 87 3.
---------+Article 87 4.
---------+Article 87 5.
---------+Article 87 6.
------+Article 88 Submission of an opinion to the Commission
---------+Article 88 1.
---------+Article 88 2.
---------+Article 88 3.
---+CHAPTER XII Delegated powers and committee procedure
------+Article 89 Exercise of the delegation
---------+Article 89 1.
---------+Article 89 2.
---------+Article 89 3.
---------+Article 89 4.
---------+Article 89 5.
---------+Article 89 6.
------+Article 90 Committee procedure
---------+Article 90 1.
---------+Article 90 2.
---------+Article 90 3.
---------+Article 90 4.
---+CHAPTER XIII Amendments
------+Article 91 Amendments to Regulation (EU) 2019/1020
------+Article 92 Amendment to Directive 2008/98/EC
---+CHAPTER XIV Final provisions
------+Article 93 Penalties
------+Article 94 Review
---------+Article 94 1.
---------+Article 94 2.
---------+Article 94 3.
---------+Article 94 4.
---------+Article 94 5.
---------+Article 94 6.
------+Article 95 Repeal and transitional rules
------+Article 96 Entry into force and application
---------+Article 96 1.
---------+Article 96 2.
---+ANNEX I
---+ANNEX II
---+ANNEX III
---+ANNEX IV
---+ANNEX V
---+ANNEX VI
---+ANNEX VII
---+ANNEX VIII
---+ANNEX IX
---+ANNEX X
---+ANNEX XI
---+ANNEX XII
---+ANNEX XIII
---+ANNEX XIV
---+ANNEX XV
 English - European Union - Environment -

REGULATION (EU) 2023/1542 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 12 July 2023 concerning batteries and waste batteries, amending Directive 2008/98/EC and Regulation (EU) 2019/1020 and repealing Directive 2006/66/EC (Text with EEA relevance)

REGULATION (EU) 2023/1542 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL

of 12 July 2023

concerning batteries and waste batteries, amending Directive 2008/98/EC and Regulation (EU) 2019/1020 and repealing Directive 2006/66/EC

(Text with EEA relevance)

This Regulation shall be binding in its entirety and directly applicable in all Member States.

1. Overzicht

,
CHAPTER I General provisions CHAPTER I General provisions
CHAPTER II Sustainability and safety requirements CHAPTER II Sustainability and safety requirements
CHAPTER III Labelling, marking and information requirements CHAPTER III Labelling, marking and information requirements
CHAPTER IV Conformity of batteries CHAPTER IV Conformity of batteries
CHAPTER V Notification of conformity assessment bodies CHAPTER V Notification of conformity assessment bodies
CHAPTER VI Obligations of economic operators other than the obligations in Chapters VII and VIII CHAPTER VI Obligations of economic operators other than the obligations in Chapters VII and VIII
CHAPTER VII Obligations of economic operators as regards battery due diligence policies CHAPTER VII Obligations of economic operators as regards battery due diligence policies
CHAPTER VIII Management of waste batteries CHAPTER VIII Management of waste batteries
CHAPTER IX Digital battery passport CHAPTER IX Digital battery passport
CHAPTER X Union market surveillance and Union safeguard procedures CHAPTER X Union market surveillance and Union safeguard procedures
CHAPTER XI Green public procurement and procedure for amending restrictions on substances CHAPTER XI Green public procurement and procedure for amending restrictions on substances
CHAPTER XII Delegated powers and committee procedure CHAPTER XII Delegated powers and committee procedure
CHAPTER XIII Amendments CHAPTER XIII Amendments
CHAPTER XIV Final provisions CHAPTER XIV Final provisions
ANNEX I



ANNEX I

▼M3



Column 1

Designation of the substance or group of substances

Column 2

Conditions of restriction

1.  Mercury CAS No 7439-97-6 EC No 231-106-7 and its compounds

Batteries, whether or not present in and incorporated into appliances, light means of transport or other vehicles, shall not contain more than 0,0005  % of mercury (expressed as mercury metal) by weight.

2.  Cadmium CAS No 7440-43-9 EC No 231-152-8 and its compounds

1.  Portable batteries, whether or not present in and incorporated into appliances, light means of transport or other vehicles, shall not contain more than 0,002  % of cadmium (expressed as cadmium metal) by weight.

2.  Electric vehicle and SLI batteries, incorporated in vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858 shall not contain more than 0,01  % of cadmium (expressed as cadmium metal) by weight in homogeneous material.

3.  Point 2 shall not apply to electric vehicle batteries used as spare parts for electric vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858 placed on the market before 31 December 2008.

3.  Lead CAS No 7439-92-1 EC No 231-100-4 and its compounds

1.  From 18 August 2024, portable batteries, whether or not present in and incorporated into appliances, shall not contain more than 0,01  % of lead (expressed as lead metal) by weight.

2.  The restriction set out in point 1 shall not apply to portable zinc-air button cells until 18 August 2028.

3.  Portable batteries incorporated in vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858, shall not contain more than 0,1  % of lead (expressed as lead metal) by weight in homogeneous material.

4.  Point 3 shall not apply to Portable Batteries incorporated in, or used as spare parts for, vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858, type approved before 1 January 2024.

5.  Electric vehicle batteries incorporated in vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858, shall not contain more than 0,1  % of lead (expressed as lead metal) by weight in homogeneous material.

 

6.  Point 5 shall not apply to:

(a)  electric vehicle batteries used in high voltage systems (2) incorporated in, or used as spare part for, in vehicles of the categories M1 and N1, as defined in Regulation (EU) 2018/858 and type approved before 1 January 2019;

(b)  electric vehicle batteries not covered by point (a) of this point incorporated in or used as spare part for vehicles, including special purpose vehicles, of the categories M1 and N1, as defined in Regulation (EU) 2018/858, and type approved before 1 January 2024.

7.  SLI batteries incorporated in vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858, shall not contain more than 0,1  % of lead (expressed as lead metal) by weight in homogeneous material.

 

8.  Point 7 shall not apply to:

(a)  SLI batteries used in 12 V applications for vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858 (3);

(b)  SLI batteries used in 24 V applications in special purpose vehicles of the categories M1 and N1 as defined in Regulation (EU) 2018/858 (4);

(c)  SLI batteries used in other applications than those covered by points (a) and (b) of this point in vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858 that are type approved before 1 January 2024.

4.  Hexavalent chromium CAS No 18540-29-9EC No 606-053-1 and its compounds

Batteries incorporated in vehicles, including special purpose vehicles, of the categories M1 and N1 as defined in Regulation (EU) 2018/858, shall not contain more than 0,1  % of hexavalent chromium, expressed as hexavalent chromium metal, by weight in homogeneous material.
(1)   

Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits (OJ L 96, 29.3.2014, p. 357, ELI: http://data.europa.eu/eli/dir/2014/35/oj).

(2)   

Systems that have a voltage of > 75 V DC as provided for in Article 1 of Directive 2014/35/EU of the European Parliament and of the Council (1).

(3)   

This exemption shall be reviewed in 2030.

(4)   

This exemption shall be reviewed in 2030.

▼B

ANNEX II



ANNEX II

CARBON FOOTPRINT

1.   Scope

This Annex provides essential elements on how to calculate the carbon footprint.

The methodology for calculation and verification of the carbon footprint to be provided for by means of the delegated act adopted pursuant to Article 7 shall build on the essential elements included in this Annex, be in compliance with the latest version of the Commission Product Environmental Footprint (PEF) method and relevant Product Environmental Footprint Category Rules (PEFCRs) and reflect the international agreements and technical/scientific progress in the area of life cycle assessment.

The calculation of the life cycle carbon footprint shall be based on the bill of materials, the energy and the auxiliary materials used in a specific manufacturing plant to produce a specific battery model. In particular, the electronic components, for example battery management units and safety units, and the cathode materials shall be accurately identified, as they can become the main contributor for the battery carbon footprint.

2.   Definitions

For the purposes of this Annex, the following definitions apply:

(a) 

‘activity data’ means the information associated with processes while modelling Life Cycle Inventories (LCI), whereby the aggregated LCI results of the process chains that represent the activities of a process are each multiplied by the corresponding activity data and then combined to derive the carbon footprint associated with that process;

(b) 

‘bill of materials’ means a list of the raw materials, sub-assemblies, intermediate assemblies, sub-components and parts, and the quantities of each, needed to manufacture the battery;

(c) 

‘company-specific data’ means data that are directly measured or collected from one or multiple facilities (site-specific data) that are representative of the activities of the company, such data are also known as ‘primary data’;

(d) 

‘functional unit’ means the qualitative and quantitative aspects of the functions, services, or both, provided by the battery;

(e) 

‘life cycle’ means the consecutive and interlinked stages of a product system, from raw material acquisition or generation from natural resources to final disposal (ISO 14040:2006 or an equivalent standard);

(f) 

‘life cycle inventory (LCI)’ means the combined set of exchanges of elementary, waste and product flows in an LCI dataset;

(g) 

‘life cycle inventory (LCI) dataset’ means a document or file with life cycle information on a specified product or other reference, such as the site or process, covering descriptive metadata and quantitative life cycle inventory, which could include a unit process dataset, partially aggregated or an aggregated dataset;

(h) 

‘reference flow’ means the measure of the outputs from processes in a given product system required to fulfil the function expressed by the functional unit (based on ISO 14040:2006 or an equivalent standard);

(i) 

‘secondary data’ means data that are not directly collected or measured from a specific process within the supply-chain of the company or estimated by that company, but that are sourced from a third party LCI database or other sources; such data include industry average data, for example from published production data, government statistics, and industry associations, as well as literature studies, engineering studies and patents, and can also be based on financial data, and contain proxy data and other generic data; and also include primary data that go through a horizontal aggregation step;

(j) 

‘system boundary’ means the aspects included or excluded from the life cycle stages.

Additionally, the harmonised rules for the calculation of the carbon footprint of batteries shall include any further definition necessary for their interpretation.

3.   Functional unit and reference flow

The functional unit is defined as one kWh (kilowatt-hour) of the total energy provided by the battery system over the battery’s service life, measured in kWh. The total energy is obtained from the number of cycles multiplied by the amount of delivered energy over each cycle.

The reference flow is the weight of battery needed to fulfil a specific function and shall be measured in kg of battery per kWh of the total energy delivered by the battery over its service life. All quantitative input and output data collected by the manufacturer to quantify the carbon footprint shall be calculated in relation to the reference flow.

By way of exception to the first paragraph, for back-up batteries that have as their primary function to ensure continuity of a power source, the functional unit is defined as the ability to provide one kWmin (kilowatt-minute) of backup power capability at any moment over the lifetime of the battery. Accordingly, the reference flow for back-up batteries is the weight of battery needed to fulfil the defined function and shall be measured in kg of battery per kWmin of backup power capability divided by the service life of the battery in years. All quantitative input and output data collected by manufacturers of back-up batteries to quantify the carbon footprint shall be calculated in relation to that reference flow.

In exceptional cases, such as for batteries for hybrid non -plug-in vehicles, the methodology may define a different functional unit.

4.   System boundary

The following life cycle stages and the processes involved therein shall be included in the system boundary:



Life cycle stage

Processes involved

Raw material acquisition and pre-processing

Includes mining and other relevant sourcing, pre-processing and transport of active materials, up to the manufacturing of battery cells and battery components (active materials, separator, electrolyte, casings, active and passive battery components), and electric or electronic components.

Main product production

Assembly of battery cells and assembly of batteries with the battery cells and the electric or electronic components

Distribution

Transport to the point of sale

End of life and recycling

Collection, dismantling and recycling

The following processes involved in the life cycle stages shall be excluded from the system boundary:

— 
manufacturing of equipment for the assembly and recycling of batteries, as carbon footprint impacts have been calculated as negligible in the PEFCRs for high specific energy rechargeable batteries for mobile applications;
— 
the battery assembly process using the original equipment manufacturer (OEM) system components; this process corresponds for the most part to mechanical assembly and it is included inside the OEM equipment or vehicle assembly line; the consumption of energy and material for this specific process is negligible when compared to the manufacturing process of OEM components.

The use phase shall be excluded from the life cycle carbon footprint calculations, as it is not under the direct influence of manufacturers except where it is demonstrated that choices made by battery manufacturers at the design stage can make a non-negligible contribution to that impact.

5.   Use of company-specific and secondary datasets

Due to the high number of battery components and the complexity of manufacturing processes, the economic operator shall limit, where justified, the use of company specific data to process and component analysis of the battery-specific parts.

In particular, all activity data related to the battery’s anode, cathode, electrolyte, separator and cell-casing shall refer to a specific battery model produced in a specific production plant. Accordingly, no default activity data shall be used. The battery-specific activity data shall be used in combination with the relevant PEF-compliant secondary datasets.

As the carbon footprint declaration is specific to a battery model produced in a defined production site, sampling of data collected from different plants producing the same battery model shall not be allowed.

Where there is a change in the bill of materials or energy mix used to produce a battery model, the carbon footprint for that battery model shall be recalculated.

The harmonised rules to be provided for via a delegated act as referred to in Article 7(1) shall include detailed modelling of the following life cycle stages:

— 
raw material acquisition and pre-processing,
— 
production,
— 
distribution,
— 
own electricity production,
— 
end of life.

6.   Carbon footprint impact assessment

The carbon footprint of the battery shall be calculated using the ‘climate change’ life cycle impact assessment method recommended in the 2019 Joint Research Centre report entitled ‘Suggestions for updating the Product Environmental Footprint (PEF) method’.

The results shall be provided as characterised results without normalisation and weighting. The list of characterization factors to be used is available at the European Platform on Life Cycle Assessment (LCA).

7.   Offsets

Offsets are calculated relative to a baseline that represents a hypothetical scenario for what emissions would have been in the absence of the mitigation project that generates the offsets.

Offsets shall not be included in the carbon footprint declaration, but may be reported separately as additional environmental information and used for communication purposes.

8.   Carbon footprint performance classes

Depending on the distribution of the values in the carbon footprint declarations of batteries placed on the market, a meaningful number of classes of performance shall be identified, with category A being the best class with the lowest carbon footprint life cycle impact, to enable market differentiation of the battery categories referred to in Article 7(1).

The setting of the threshold for each class of performance, as well as the width of that class, shall be based on the distribution of performances of the battery categories referred to in Article 7(1) placed on the market in the previous three years, the expected technological improvements, and other technical factors.

9.   Maximum carbon thresholds

Based on the information collected through the carbon footprint declarations and the relative distribution of the carbon footprint performance classes of battery models placed on the market, and taking into account the scientific and technical progress in the field, the Commission shall set maximum life cycle carbon footprint thresholds for the battery categories referred to in Article 7(1), after having carried out a dedicated impact assessment to determine the values for the thresholds.

In setting maximum life cycle carbon footprint thresholds referred to in the first subparagraph, the Commission shall take into account the relative distribution of the carbon footprint values for batteries on the market, the extent of progress in reducing the carbon footprint of batteries placed on the market and the actual and potential contribution of those life cycle carbon footprint thresholds to the Union’s objectives on sustainable mobility and climate neutrality by 2050.
ANNEX III



ANNEX III

ELECTROCHEMICAL PERFORMANCE AND DURABILITY PARAMETERS FOR PORTABLE BATTERIES OF GENERAL USE

Part A

Parameters for non-rechargeable batteries

1. Minimum average duration: minimum average time reached by a sample of batteries on discharge when used under specific conditions, such as temperature and relative humidity.

2. Delayed discharge performance: the relative decrease of the minimum average duration, with the initially measured minimum average duration as the reference point, after a defined period and under specific conditions, such as temperature and relative humidity.

3. Resistance to leakage: resistance to unplanned escape of electrolyte, gas or other material.

Part B

Parameters for rechargeable batteries

1. Rated capacity: the capacity value of a battery, under specific conditions, such as temperature and relative humidity, and declared by the manufacturer.

2. Charge (capacity) ( 7 ) retention: the capacity that a battery can deliver after storage, under specific conditions, such as temperature and relative humidity, for a specific time, without a subsequent recharge and expressed as a percentage of the rated capacity.

3. Charge (capacity) recovery: the capacity that a battery can deliver with a subsequent recharge after storage, under specific conditions, such as temperature and relative humidity, for a specific time and expressed as percentage of the rated capacity.

4. Endurance in cycles the number of charge and discharge cycles a battery can perform under specific conditions, such as temperature and relative humidity, before the capacity drops below a specified fraction of the rated capacity.

5. Resistance to leakage: resistance to unplanned escape of electrolyte, gas or other material.
ANNEX IV



ANNEX IV

ELECTROCHEMICAL PERFORMANCE AND DURABILITY REQUIREMENTS FOR LMT BATTERIES, INDUSTRIAL BATTERIES WITH A CAPACITY GREATER THAN 2 KWH AND ELECTRIC VEHICLE BATTERIES

For the purposes of this Annex the following definitions apply:

(1) 

‘Rated capacity’ means the total number of ampere-hours (Ah) that can be withdrawn from a fully charged battery under reference conditions.

(2) 

‘Capacity fade’ means the decrease over time and upon usage in the amount of charge that a battery can deliver at the rated voltage, with respect to the original rated capacity.

(3) 

‘Power’ means the amount of energy that a battery is capable of providing over a given period under reference conditions.

(4) 

‘Power fade’ means the decrease over time and upon usage in the amount of power that a battery can deliver at the rated voltage.

(5) 

‘Internal resistance’ means the opposition to the flow of current within a cell or a battery under reference conditions, that is, the sum of electronic resistance and ionic resistance to the contribution to total effective resistance including inductive/capacitive properties.

(6) 

‘Energy round trip efficiency’ means the ratio of the net energy delivered by a battery during a discharge test to the total energy required to restore the initial state of charge by a standard charge.

Part A

Parameters related to electrochemical performance and durability

1. Rated capacity (in Ah) and capacity fade (in %).

2. Power (in W) and power fade (in %).

3. Internal resistance (in Ω) and internal resistance increase (in %).

4. Where applicable, energy round trip efficiency and its fade (in %).

5. The expected life-time of the battery under the reference conditions for which it has been designed, in terms of cycles, except for non-cycle applications, and calendar years.

Part B

Elements to explain the measurements for parameters listed in Part A

1. Applied discharge rate and charge rate.

2. Ratio between nominal battery power (W) and battery energy (Wh).

3. Depth of discharge in the cycle-life test.

4. Power capability at 80 % and 20 % state of charge.

5. Any calculations performed with the measured parameters, if applicable.
ANNEX V



ANNEX V

SAFETY PARAMETERS

1.   Thermal shock and cycling

This test shall be designed to evaluate changes in the integrity of the battery arising from expansion and contraction of cell components upon exposure to extreme and sudden changes in temperature, and potential consequences of such changes. During a thermal shock, the battery shall be exposed to two temperature limits and held at each temperature limit for a specified period.

2.   External short circuit protection

This test shall evaluate the safety performance of a battery when applying an external short circuit. The test can evaluate the activation of the overcurrent protection device or the ability of cells to withstand the current without reaching a hazardous situation (e.g. thermal runaway, explosion, fire). The main risk factors are heat generation at cell level and electrical arcing, which can damage circuitry or lead to reduced isolation resistance.

3.   Overcharge protection

This test shall evaluate the safety performance of a battery in overcharge situations. The main safety risks during overcharge are the decomposition of the electrolyte, cathode and anode breakdown, exothermic decomposition of the solid electrolyte interphase (SEI) layer, separator degradation, and lithium plating, which can lead to self-heating of the battery and thermal runaway. The factors affecting the outcome of the test shall, as a minimum, include, the charging rate and the finally reached state of charge. The protection can be ensured either by voltage control (interruption after reaching the limit charging voltage) or current control (interruption after exceeding maximum charging current).

4.   Over-discharge protection

This test shall evaluate the safety performance of a battery in over-discharge situations. Safety risks during over-discharge include polarity reversal leading to oxidation of the anode current collector (Copper) and to plating on the cathode side. Even minor over-discharge can cause dendrite formation and ultimately short-circuiting.

5.   Over-temperature protection

This test shall evaluate the effect of temperature control failure or failure of other features for protection against internal overheating during operation.

6.   Thermal propagation protection

This test shall evaluate the safety performance of a battery in thermal propagation situations. A thermal runaway in one cell can cause a cascading reaction throughout the entire battery which can be composed of numerous cells. It can lead to severe consequences including a significant gas release. The test shall take into account the tests that are under development for transport applications by ISO and the UN Global Technical Regulation.

7.   Mechanical damage by external forces

These tests shall simulate one or more situations in which a battery is accidentally exposed to mechanical stresses and remains operational for the purpose for which it was designed. The criteria to simulate these situations should reflect real life uses.

8.   Internal short circuit

This test shall evaluate the safety performance of a battery in internal short-circuit situations. The occurrence of internal short circuits, one of the main concerns for battery manufacturers, potentially leads to venting, thermal runaway, and sparking which can ignite the electrolyte vapours escaping from the cell. The generation of such internal short circuits can be triggered by manufacturing imperfections, the presence of impurities in the cells or dendritic growth of lithium, and is the cause of most in-field safety incidents. Multiple internal short circuit scenarios are possible (e.g. electrical contact of cathode/anode, aluminium current collector/copper current collector, aluminium current collector/anode) each with a different contact resistance.

9.   Thermal abuse

During this test, the battery shall be exposed to elevated temperatures (in IEC 62619 the temperature is 85 °C) which can trigger exothermal decomposition reactions and lead to a thermal runaway in the cell.

10.   Fire test

The risk of explosion shall be assessed by exposing the battery to fire.

11.   Emission of gases

Batteries can contain significant amounts of potentially hazardous materials, for example highly flammable electrolytes, corrosive and toxic components. If exposed to certain conditions, the integrity of the battery could be compromised, resulting in the release of hazardous gases. Therefore, it is important to identify emissions of gases from substances released from the battery during tests: the risk of toxic gases emitted from non-aqueous electrolytes shall be properly taken into account for all safety parameters listed in points 1 to 10.
ANNEX VI



ANNEX VI

LABELLING, MARKING AND INFORMATION REQUIREMENTS

Part A: General information on batteries

Information on the label of a battery shall comprise the following information regarding the battery:

1. 

information identifying the manufacturer in accordance with Article 38(7);

2. 

the battery category and information identifying the battery in accordance with Article 38(6);

3. 

the place of manufacture (geographical location of a battery manufacturing plant);

4. 

the date of manufacture (month and year);

5. 

the weight;

6. 

the capacity;

7. 

the chemistry;

8. 

the hazardous substances present in the battery, other than mercury, cadmium or lead;

9. 

usable extinguishing agent;

10. 

critical raw materials present in the battery in a concentration of more than 0,1 % weight by weight.

Part B: Symbol for separate collection of batteries

image

Part C: QR code

The QR code shall be in high contrast to the background colour and of a size that is easily readable by a commonly available QR reader, such as those integrated in hand-held communication devices.
ANNEX VII



ANNEX VII

PARAMETERS FOR DETERMINING THE STATE OF HEALTH AND EXPECTED LIFETIME OF BATTERIES

Part A

Parameters for determining the state of health of electric vehicle batteries, stationary battery energy storage systems and LMT batteries:

For electric vehicle batteries:

state of certified energy (SOCE).

For stationary battery energy storage systems and LMT batteries:

1. 

the remaining capacity;

2. 

where possible, the remaining power capability;

3. 

where possible, the remaining round trip efficiency;

4. 

the evolution of self-discharging rates;

5. 

where possible, the ohmic resistance.

Part B

Parameters for determining the expected lifetime of stationary battery energy storage systems and LMT batteries:

1. 

the date of manufacture of the battery and, where appropriate, the date of putting into service;

2. 

the energy throughput;

3. 

the capacity throughput;

4. 

the tracking of harmful events, such as the number of deep discharge events, time spent in extreme temperatures, time spent charging in extreme temperatures;

5. 

the number of full equivalent charge-discharge cycles.
ANNEX VIII



ANNEX VIII

CONFORMITY ASSESSMENT PROCEDURES

Part A

MODULE A – INTERNAL PRODUCTION CONTROL

1.   Description of the module

Internal production control is the conformity assessment procedure whereby the manufacturer fulfils the obligations set out in points 2, 3 and 4, and ensures and declares on its sole responsibility that the batteries concerned meet the requirements laid down in Articles 6, 9, 10, 12, 13 and 14 that apply to them.

2.   Technical documentation

The manufacturer shall draw up the technical documentation. The documentation shall make it possible to assess the battery’s conformity with the relevant requirements referred to in point 1 and shall include an adequate analysis and assessment of the risks.

The technical documentation shall specify the applicable requirements and cover, as far as relevant for the assessment, the design, manufacture and operation of the battery. The technical documentation shall, where applicable, contain at least the following elements:

(a) 

a general description of the battery and its intended use;

(b) 

the conceptual design and manufacturing drawings and schemes of components, sub-assemblies and circuits;

(c) 

the descriptions and explanations necessary for the understanding of the drawings and schemes referred to in point (b) and the operation of the battery;

(d) 

a specimen of the label required in accordance with Article 13;

(e) 

a list of the harmonised standards referred to in Article 15, applied in full or in part, including an indication of which parts have been applied, a list of the common specifications referred to in Article 16, applied in full or in part, including an indication of which parts have been applied, and a list of other relevant technical specifications used for measurement or calculation purposes;

(f) 

where the harmonised standards and the common specifications referred to in point (e) have not been applied or are not available, a description of the solutions adopted to meet the applicable requirements laid down in Articles 6, 9, 10, 12, 13 and 14 or to verify the compliance of batteries with those requirements;

(g) 

the results of design calculations made and the examinations carried out, and the technical or documentary evidence used; and

(h) 

the test reports.

3.   Manufacturing

The manufacturer shall take all measures necessary so that the manufacturing process and the monitoring thereof ensure the batteries comply with the technical documentation referred to in point 2 and with the applicable requirements referred to in point 1.

4.   CE marking and EU declaration of conformity

The manufacturer shall affix the CE marking to each individual battery that meets the applicable requirements referred to in point 1, or, where that is not possible or not warranted due to the nature of the battery, to the packaging and the documents accompanying the battery.

The manufacturer shall draw up an EU declaration of conformity for each battery model in accordance with Article 18 and keep it together with the technical documentation at the disposal of the national authorities for 10 years after the last battery belonging to the respective battery model has been placed on the market. The EU declaration of conformity shall identify the battery model for which it has been drawn up.

A copy of the EU declaration of conformity shall be made available to the national authorities upon request.

5.   Manufacturer’s authorised representative

The manufacturer’s obligations set out in point 4 may be fulfilled by the manufacturer’s authorised representative, on its behalf and under the manufacturer’s responsibility, provided that they are specified in the mandate.

Part B

MODULE D1 – QUALITY ASSURANCE OF THE PRODUCTION PROCESS

1.   Description of the module

Quality assurance of the production process is the conformity assessment procedure whereby the manufacturer fulfils the obligations set out in points 2, 4 and 7, and ensures and declares on its sole responsibility, without prejudice to the obligations of other economic operators in accordance with this Regulation, that the batteries concerned meet the applicable requirements laid down in Articles 7 and 8, or, at the choice of the manufacturer, all applicable requirements laid down in Articles 6 to 10 and Articles 12, 13 and 14.

2.   Technical documentation

The manufacturer shall draw up the technical documentation. The technical documentation shall make it possible to assess the battery’s conformity with the relevant requirements referred to in point 1, and shall include an adequate analysis and assessment of the risks.

The technical documentation shall specify the applicable requirements and cover, as far as relevant for the assessment, the design, manufacture and operation of the battery. The technical documentation shall, where applicable, contain at least the following elements:

(a) 

a general description of the battery and its intended use;

(b) 

the conceptual design and manufacturing drawings and schemes of components, sub-assemblies and circuits;

(c) 

the descriptions and explanations necessary for the understanding of the drawings and schemes referred to in point (b) and the operation of the battery;

(d) 

a specimen of the label required in accordance with Article 13;

(e) 

a list of the harmonised standards referred to in Article 15, the common specifications referred to in Article 16, or of both, applied, and, in the event of partly applied harmonised standards, common specifications, or both, an indication of which parts have been applied;

(f) 

a list of other relevant technical specifications used for measurement or calculation purposes and descriptions of the solutions adopted to meet the applicable requirements laid down in Articles 6 to 10 and Articles 12, 13 and 14 or to verify the compliance of batteries with those requirements, where harmonised standards, common specifications, or both, have not been applied or are not available;

(g) 

the results of design calculations made and the examinations carried out, and the technical or documentary evidence used;

(h) 

a study supporting the carbon footprint values referred to in Article 7(1) and the carbon footprint class referred to in Article 7(2), containing the calculations made in accordance with the methodology set out in the delegated act adopted pursuant to Article 7(1), fourth subparagraph, point (a), and the evidence and information determining the input data for those calculations;

(i) 

a study supporting the recycled content share referred to in Article 8, containing the calculations made in accordance with the methodology set out in the delegated act adopted pursuant to Article 8(1), second subparagraph, and the evidence and information determining the input data for those calculations; and

(j) 

the test reports.

3.   Availability of technical documentation

The manufacturer shall keep the technical documentation at the disposal of the national authorities for 10 years after the battery has been placed on the market.

4.   Manufacturing

The manufacturer shall operate an approved quality system for production, final product inspection and testing of the batteries concerned as specified in point 5, and shall be subject to surveillance as specified in point 6.

5.   Quality system

1. The manufacturer shall lodge an application for assessment of its quality system with the notified body of its choice, for the batteries concerned.

The application shall include:

(a) 

the name and address of the manufacturer and, if the application is lodged by the manufacturer’s authorised representative, its name and address as well;

(b) 

a written declaration that the same application has not been lodged with any other notified body;

(c) 

all relevant information for the battery category envisaged;

(d) 

the documentation concerning the quality system referred to in point 5.2;

(e) 

the technical documentation referred to in point 2.

2. The quality system shall ensure that the batteries comply with the applicable requirements laid down in Articles 6 to 10 and Articles 12, 13 and 14.

All the elements, requirements and provisions adopted by the manufacturer shall be documented in a systematic and orderly manner in the form of written policies, procedures and instructions. The quality system documentation shall make it possible to have a consistent interpretation of the quality programmes, plans, manuals and records.

The quality system documentation shall, in particular, contain an adequate description of:

(a) 

the quality objectives and the organisational structure, responsibilities and powers of the management with regard to product quality;

(b) 

the procedures for documenting and monitoring the parameters and data necessary for calculating and updating the recycled content share referred to in Article 8 and, where applicable, the carbon footprint values and class referred to in Article 7;

(c) 

the corresponding manufacturing, quality control and quality assurance techniques, processes and systematic actions that will be used;

(d) 

the examinations, calculations, measurements and tests that will be carried out before, during and after manufacture, and the frequency with which they will be carried out;

(e) 

the quality records, such as inspection reports and calculation, measurement and test data, calibration data, qualification reports on the personnel concerned;

(f) 

the means of monitoring the achievement of the required product quality and the effective operation of the quality system.

3. The notified body shall assess the quality system to determine whether it meets the requirements referred to in point 5.2.

It shall presume conformity with those requirements in respect of the elements of the quality system that comply with the corresponding specifications of the relevant harmonised standard.

In addition to experience in quality management systems, the auditing team shall have at least one member with experience of evaluation in the relevant product field and product technology concerned, and knowledge of the applicable requirements laid down in Articles 6 to 10 and Articles 12, 13 and 14.

The audit shall include an assessment visit to the manufacturer’s premises.

The auditing team shall review the technical documentation referred to in point 2 in order to verify the manufacturer’s ability to identify the applicable requirements laid down in Articles 6 to 10 and Articles 12, 13 and 14 and to carry out the necessary examinations, calculations, measurements and tests with a view to ensuring that the battery complies with those requirements. The auditing team shall check the reliability of data used for the calculation of the recycled content share referred to in Article 8 and, where applicable, the carbon footprint values and class referred to in Article 7 as well as the proper implementation of the relevant calculation methodology.

After having assessed the quality system, the notified body shall notify its decision to the manufacturer. The notification shall contain the conclusions of the audit and the reasons for that decision.

4. The manufacturer shall undertake to fulfil the obligations arising from the quality system as approved and to maintain it so that it remains adequate and efficient.

5. The manufacturer shall keep the notified body that has approved the quality system informed of any intended change to the quality system.

The notified body shall evaluate any proposed changes and decide whether the modified quality system will continue to meet the requirements referred to in point 5.2 or whether reassessment is necessary.

The notified body shall notify the manufacturer of its decision. The notification shall contain the conclusions of the examination and the reasoned assessment decision.

6. Surveillance under the responsibility of the notified body

1. 

The purpose of surveillance is to make sure that the manufacturer duly fulfils the obligations arising from the approved quality system.

2. 

The manufacturer shall, for assessment purposes, allow the notified body access to the manufacture, inspection, testing and storage sites and shall provide it with all necessary information, in particular:

(a) 

the quality system documentation referred to in point 5.2;

(b) 

the technical documentation referred to in point 2;

(c) 

the quality records, such as inspection reports and calculation, measurement and test data, calibration data and qualification reports on the personnel concerned.

3. 

The notified body shall carry out periodic audits to make sure that the manufacturer maintains and applies the quality system, and shall provide the manufacturer with an audit report. During such audits, the notified body shall check at least the reliability of data used for the calculation of the recycled content share referred to in Article 8 and, where applicable, the carbon footprint values and class referred to in Article 7, as well as the proper implementation of the relevant calculation methodology.

4. 

In addition, the notified body may pay unexpected visits to the manufacturer. During such visits, the notified body may, if necessary, carry out examinations, calculations, measurements and tests, or have them carried out, in order to verify that the quality system is functioning correctly. The notified body shall provide the manufacturer with a visit report and, if tests have been carried out, with a test report.

7. CE marking and EU declaration of conformity

1. 

The manufacturer shall affix the CE marking, and, under the responsibility of the notified body referred to in point 5.1, the latter’s identification number to each individual battery that meets the applicable requirements referred to in point 1, or, where that is not possible or is not warranted due to the nature of the battery, to the packaging and the documents accompanying the battery.

2. 

The manufacturer shall draw up an EU declaration of conformity for each battery model in accordance with Article 18 and keep it at the disposal of the national authorities for 10 years after the last battery belonging to the respective battery model has been placed on the market. The EU declaration of conformity shall identify the battery model for which it has been drawn up.

A copy of the EU declaration of conformity shall be made available to the national authorities upon request.

8. Availability of quality system documentation

The manufacturer shall, for a period of 10 years after the battery has been placed on the market, keep at the disposal of the national authorities:

(a) 

the quality system documentation referred to in point 5.2;

(b) 

the change referred to in point 5.5, as approved;

(c) 

the decisions and reports of the notified body referred to in points 5.5, 6.3 and 6.4.

9. Information obligations of the notified body

Each notified body shall inform its notifying authority of quality system approvals issued or withdrawn, and shall, periodically or upon request, make available to its notifying authority the list of quality system approvals refused, suspended or otherwise restricted.

Each notified body shall inform the other notified bodies of quality system approvals which it has refused, withdrawn, suspended or otherwise restricted, and, upon request, of quality system approvals which it has issued.

10. Manufacturer’s authorised representative

The manufacturer’s obligations set out in points 3, 5.1, 5.5, 7 and 8 may be fulfilled by the manufacturer’s authorised representative, on the manufacturer’s behalf and under the manufacturer’s responsibility, provided that they are specified in the mandate.

Part C

MODULE G – CONFORMITY BASED ON UNIT VERIFICATION

1.   Description of the module

Conformity based on unit verification is the conformity assessment procedure whereby the manufacturer fulfils the obligations set out in points 2, 3 and 5, and ensures and declares on its sole responsibility, without prejudice to the obligations of other economic operators in accordance with this Regulation, that the battery concerned, which has been subject to the provisions of point 4, is in conformity with the applicable requirements laid down in Articles 7 and 8, or, at the choice of the manufacturer, all applicable requirements laid down in Articles 6 to 10 and Articles 12, 13 and 14.

2.   Technical documentation

1. The manufacturer shall draw up the technical documentation and make it available to the notified body referred to in point 4. The technical documentation shall make it possible to assess the battery’s conformity with the relevant requirements referred to in point 1 and shall include an adequate analysis and assessment of the risks.

The technical documentation shall specify the applicable requirements and cover, as far as relevant for the assessment, the design, manufacture and operation of the battery.

The technical documentation shall, where applicable, contain at least the following elements:

(a) 

a general description of the battery and its intended use;

(b) 

the conceptual design and manufacturing drawings and schemes of components, sub-assemblies and circuits;

(c) 

the descriptions and explanations necessary for the understanding of the drawings and schemes referred to in point (b) and the operation of the battery;

(d) 

a specimen of the label required in accordance with Article 13;

(e) 

a list of the harmonised standards referred to in Article 15, the common specifications referred to in Article 16, or of both, applied, and, in the event of partly applied harmonised standards, common specifications, or both, an indication of which parts have been applied;

(f) 

a list of other relevant technical specifications used for measurement or calculation purposes and descriptions of the solutions adopted to meet the applicable requirements referred to in point 1 or to verify the conformity of batteries with those requirements, where harmonised standards, common specifications, or both, have not been applied or are not available;

(g) 

the results of design calculations made and the examinations carried out, and the technical or documentary evidence used;

(h) 

a study supporting the carbon footprint values and class referred to in Article 7, containing the calculations made in accordance with the methodology set out in the delegated act adopted pursuant to Article 7(1), fourth subparagraph, point (a), and the evidence and information determining the input data for those calculations;

(i) 

a study supporting the recycled content share referred to in Article 8, containing the calculations made in accordance with the methodology set out in the delegated act adopted pursuant to Article 8(1), second subparagraph, and the evidence and information determining the input data for those calculations; and

(j) 

the test reports.

2. The manufacturer shall keep the technical documentation at the disposal of the national authorities for 10 years after the battery has been placed on the market.

3. Manufacturing

The manufacturer shall take all measures necessary so that the manufacturing process and the monitoring thereof ensure that the manufactured battery is in conformity with the applicable requirements referred to in point 1.

4. Verification

1. 

A notified body chosen by the manufacturer shall carry out appropriate examinations, calculations, measurements and tests, as set out in the relevant harmonised standards referred to in Article 15, common specifications referred to in Article 16, or both, or equivalent tests, to check the conformity of the battery with the applicable requirements referred to in point 1, or have them carried out. In the absence of such a harmonised standard or common specification, the notified body concerned shall decide on the appropriate examinations, calculations, measurements and tests to be carried out.

The notified body shall issue a certificate of conformity in respect of the examinations, calculations, measurements and tests carried out and shall affix its identification number to the approved battery, or have it affixed under its responsibility.

2. 

The manufacturer shall keep the certificates of conformity at the disposal of the national authorities for 10 years after the battery has been placed on the market.

5. CE marking and EU declaration of conformity

The manufacturer shall affix the CE marking and, under the responsibility of the notified body referred to in point 4, the latter’s identification number to each battery that meets the applicable requirements referred to in point 1, or, where that is not possible or is not warranted due to the nature of the battery, to the packaging and the documents accompanying the battery.

The manufacturer shall draw up an EU declaration of conformity in accordance with Article 18 for each battery and keep it at the disposal of the national authorities for 10 years after the battery has been placed on the market. The EU declaration of conformity shall identify the battery for which it has been drawn up.

A copy of the EU declaration of conformity shall be made available to the national authorities upon request.

6. Manufacturer’s authorised representative

The manufacturer’s obligations set out in points 2.2, 4.2 and 5 may be fulfilled by the manufacturer’s authorised representative, on the manufacturer’s behalf and under the manufacturer’s responsibility, provided that they are specified in the mandate.
ANNEX IX



ANNEX IX

EU DECLARATION OF CONFORMITY No* …

* (identification number of the declaration)

1. Battery model (product, category, and batch or serial number):

2. Name and address of the manufacturer and, where applicable, its authorised representative:

3. This declaration of conformity is issued under the sole responsibility of the manufacturer.

4. Object of the declaration (description of the battery and identification allowing traceability, and which may, where appropriate, include an image of the battery):

5. The object of the declaration described in point 4 is in conformity with the relevant Union harmonisation legislation: … (reference to the other Union acts applied).

6. References to the relevant harmonised standards or the common specifications used or references to the other technical specifications in relation to which conformity is declared:

7. The notified body … (name, address, number) … performed … (description of intervention) … and issued the certificate(s): … (details, including its date, and, where appropriate, information on the duration of and conditions for its validity).

8. Additional information

Signed for and on behalf of:

(place and date of issue):

(name, function) (signature)
ANNEX X



ANNEX X

LIST OF RAW MATERIALS AND RISK CATEGORIES

1. Raw materials:

(a) 

cobalt;

(b) 

natural graphite;

(c) 

lithium;

(d) 

nickel;

(e) 

chemical compounds based on the raw materials listed in points (a) to (d), which are necessary for the manufacturing of the active materials of batteries.

2. Social and environmental risk categories:

(a) 

environment, climate and human health, considering direct, induced, indirect and cumulative effects, including:

(i) 

air, including air pollution such as greenhouse gas emissions,

(ii) 

water, including seabed and marine environment, and including water pollution, water use, water quantities (flooding or droughts) and access to water,

(iii) 

soil, including soil pollution, soil erosion, land use and land degradation,

(iv) 

biodiversity, including damage to habitats, wildlife, flora and ecosystems, including ecosystem services,

(v) 

hazardous substances,

(vi) 

noise and vibration,

(vii) 

plant safety,

(viii) 

energy use,

(ix) 

waste and residues;

(b) 

human rights, labour rights and industrial relations, including:

(i) 

occupational health and safety,

(ii) 

child labour,

(iii) 

forced labour,

(iv) 

discrimination,

(v) 

trade union freedoms;

(c) 

community life, including that of indigenous peoples.

3. The international instruments covering the risks referred to in point 2 include:

(a) 

the Ten Principles of the United Nations Global Compact;

(b) 

the UNEP Guidelines for Social Life Cycle Assessment of Products;

(c) 

the Convention on Biological Diversity, in particular Decision COP VIII/28 – Voluntary guidelines on Biodiversity-Inclusive impact assessment;

(d) 

the UN Paris Agreement;

(e) 

the eight fundamental ILO Conventions as defined under the ILO Declaration on Fundamental Principles and Rights at Work;

(f) 

any other international environmental conventions that are binding upon the Union or its Member States;

(g) 

the ILO Declaration on Fundamental Principles and Rights at Work;

(h) 

the International Bill of Human Rights, including the International Covenant on Civil and Political Rights and the International Covenant on Economic, Social and Cultural Rights.

4. The internationally recognized due diligence instruments applicable to the due diligence requirements laid down in Chapter VII of this Regulation:

(a) 

the International Bill of Human Rights, including the International Covenant on Civil and Political Rights and the International Covenant on Economic, Social and Cultural Rights;

(b) 

the UN Guiding Principles on Business and Human Rights;

(c) 

the OECD Guidelines for Multinational Enterprises;

(d) 

the ILO Tripartite Declaration of Principles concerning Multinational Enterprises and Social Policy;

(e) 

the OECD Due Diligence Guidance for Responsible Business Conduct;

(f) 

the OECD Due Diligence Guidance for Responsible Supply Chains of Minerals from Conflict-Affected and High-Risk Areas.
ANNEX XI



ANNEX XI

CALCULATION OF COLLECTION RATES FOR WASTE PORTABLE BATTERIES AND WASTE LMT BATTERIES

1. Producers of the relevant category of batteries or, where appointed in accordance with Article 57(1), producer responsibility organisations, and Member States shall calculate the collection rate as the percentage obtained by dividing the weight of waste batteries, collected in accordance with Articles 59, 60 and 69, respectively, in a given calendar year in a Member State by the average weight of such batteries that producers either make available on the market directly to end-users or deliver to third parties in order to make them available on the market to end-users in that Member State during the three preceding calendar years. The collection rate shall be calculated for portable batteries in accordance with Article 59, and for LMT batteries in accordance with Article 60 respectively.



Year

Data collection

Calculation

Reporting requirement

Year 1

Sales in year 1 (S1)

 

 

 

Year 2

Sales in year 2 (S2)

 

 

 

Year 3

Sales in year 3 (S3)

 

 

 

Year 4

Sales in year 4 (S4)

Collection in year 4 (C4)

Collection rate (CR4) = 3*C4/(S1+S2+S3)

CR4

Year 5

Sales in year 5 (S5)

Collection in year 5 (C5)

Collection rate (CR5) = 3*C5/(S2+S3+S4)

CR5

Etc.

Etc.

Etc.

Etc.

 

2. Producers of the relevant category of batteries or, where appointed in accordance with Article 57(1), producer responsibility organisations, and Member States shall calculate the annual sales of batteries to end-users in a given year, as the weight of such batteries made available on the market for the first time within the territory of the Member State in the year concerned, excluding any batteries that have left the territory of that Member State in that year, before being sold to the end-users. Those sales shall be calculated separately for portable batteries and for LMT batteries.

3. For each battery, only the first time it is made available on the market in a Member State shall be counted.

4. The calculation provided for in points 1 and 2 shall be based on collected data or statistically significant estimates based on collected data.
ANNEX XII



ANNEX XII

STORAGE AND TREATMENT, INCLUDING RECYCLING, REQUIREMENTS

Part A: Storage and treatment requirements

1. Treatment shall, as a minimum, include removal of all fluids and acids.

2. Treatment and any storage, including temporary storage, at treatment facilities, including recycling facilities, shall take place in sites with impermeable surfaces and suitable weatherproof covering or in suitable containers.

3. Waste batteries in treatment facilities, including recycling facilities, shall be stored in such a way that they are not mixed with waste from conductive or combustible materials.

4. Special precautions and safety measures shall be in place for the treatment of waste lithium-based batteries during handling, sorting and storage. Such measures shall include protection from exposure to:

(a) 

excessive heat, such as high temperatures, fire or direct sunlight;

(b) 

water, such as precipitation and flooding;

(c) 

any crushing or physical damage.

Waste lithium-based batteries shall be stored in their normally installed orientation, that is, never inverted, and in well-ventilated areas and they shall be covered with a high voltage rubber isolation. Storage facilities for waste lithium-based batteries shall be marked with a warning sign.

5. Mercury shall be separated during treatment into an identifiable stream, which is safely immobilised and disposed of and cannot cause adverse effects on human health or the environment.

6. Cadmium shall be separated during treatment into an identifiable stream, which is given a safe destination and cannot cause adverse effects on human health or the environment.

Part B: Targets for recycling efficiency

1. No later than 31 December 2025, recycling shall achieve at least the following targets for recycling efficiency:

(a) 

recycling of 75 % by average weight of lead-acid batteries;

(b) 

recycling of 65 % by average weight of lithium-based batteries;

(c) 

recycling of 80 % by average weight of nickel-cadmium batteries;

(d) 

recycling of 50 % by average weight of other waste batteries.

2. No later than 31 December 2030, recycling shall achieve at least the following targets for recycling efficiency:

(a) 

recycling of 80 % by average weight of lead-acid batteries;

(b) 

recycling of 70 % by average weight of lithium-based batteries.

Part C: Targets for recovery of materials

1. No later than 31 December 2027, all recycling shall achieve at least the following targets for recovery of materials:

(a) 

90 % for cobalt;

(b) 

90 % for copper;

(c) 

90 % for lead;

(d) 

50 % for lithium;

(e) 

90 % for nickel.

2. No later than 31 December 2031, all recycling shall achieve at least the following targets for recovery of materials:

(a) 

95 % for cobalt;

(b) 

95 % for copper;

(c) 

95 % for lead;

(d) 

80 % for lithium;

(e) 

95 % for nickel.
ANNEX XIII



ANNEX XIII

INFORMATION TO BE INCLUDED IN THE BATTERY PASSPORT

1.   PUBLICLY ACCESSIBLE INFORMATION RELATING TO THE BATTERY MODEL

A battery passport shall include the following information relating to the battery model, which shall be accessible to the public:

(a) 

the information specified in Part A of Annex VI;

(b) 

the material composition of the battery, including its chemistry, hazardous substances present in the battery, other than mercury, cadmium or lead, and critical raw materials present in the battery;

(c) 

the carbon footprint information referred to in Article 7(1) and (2);

(d) 

information on responsible sourcing as indicated in the report on battery due diligence policy referred to in Article 52(3);

(e) 

recycled content information as contained in the documentation referred to in Article 8(1);

(f) 

the share of renewable content;

(g) 

rated capacity (in Ah);

(h) 

minimal, nominal and maximum voltage, with temperature ranges when relevant;

(i) 

original power capability (in Watts) and limits, with temperature range when relevant;

(j) 

expected battery lifetime expressed in cycles, and reference test used;

(k) 

capacity threshold for exhaustion (only for electric vehicle batteries);

(l) 

temperature range the battery can withstand when not in use (reference test);

(m) 

period for which the commercial warranty for the calendar life applies;

(n) 

initial round trip energy efficiency and at 50 % of cycle-life;

(o) 

internal battery cell and pack resistance;

(p) 

c-rate of relevant cycle-life test.

▼C4

(q) 

the marking requirements laid down in Article 13(4) and (5);

▼B

(r) 

the EU declaration of conformity referred to in Article 18;

(s) 

the information regarding the prevention and management of waste batteries laid down in Article 74(1), points (a) to (f).

2.   INFORMATION RELATING TO THE BATTERY MODEL ACCESSIBLE ONLY TO PERSONS WITH A LEGITIMATE INTEREST AND THE COMMISSION

A battery passport shall include the following information relating to the battery model, which shall be accessible only to persons with a legitimate interest and the Commission:

(a) 

detailed composition, including materials used in the cathode, anode and electrolyte;

(b) 

part numbers for components and contact details of sources for replacement spares;

(c) 

dismantling information, including at least:

— 
exploded diagrams of the battery system/pack showing the location of battery cells,
— 
disassembly sequences,
— 
type and number of fastening techniques to be unlocked,
— 
tools required for disassembly,
— 
warnings if risk of damaging parts exist,
— 
amount of cells used and layout;
(d) 

safety measures.

3.   INFORMATION ACCESSIBLE ONLY TO NOTIFIED BODIES, MARKET SURVEILLANCE AUTHORITIES AND THE COMMISSION

A battery passport shall include the following information relating to the battery model, which shall be accessible only to notified bodies, market surveillance authorities and the Commission:

— 
results of test reports proving compliance with the requirements laid down in this Regulation or any delegated or implementing act adopted pursuant to this Regulation.

4.   INFORMATION AND DATA RELATING TO AN INDIVIDUAL BATTERY ACCESSIBLE ONLY TO PERSONS WITH A LEGITIMATE INTEREST

A battery passport shall include the following specific information and data relating to an individual battery, which shall be accessible only to persons with a legitimate interest:

(a) 

the values for performance and durability parameters referred to in Article 10(1), when the battery is placed on the market and when it is subject to changes in its status;

(b) 

information on the state of health of the battery pursuant to Article 14;

(c) 

information on the status of the battery, defined as ‘original’, ‘repurposed’, ‘re-used’, ‘remanufactured’ or ‘waste’;

(d) 

information and data resulting from its use, including the number of charging and discharging cycles and negative events, such as accidents, as well as periodically recorded information on the operating environmental conditions, including temperature, and on the state of charge.
ANNEX XIV



ANNEX XIV

MINIMUM REQUIREMENTS FOR SHIPMENTS OF USED BATTERIES

1. In order to distinguish between used and waste batteries, where the holder, meaning the natural or legal person in possession of the used batteries or the waste batteries, claims that it intends to ship or is shipping used batteries and not waste batteries, that holder shall be required to have available the following to substantiate that claim:

(a) 

a copy of the invoice and contract relating to the sale or transfer of ownership of the batteries which states that the batteries are destined for direct re-use and that they are fully functional;

(b) 

evidence of evaluation or testing in the form of a copy of the records, such as the certificate of testing, proof of functionality for every battery or fraction thereof in the consignment, and the protocol containing all information on the record in accordance with point 3;

(c) 

a declaration made by the holder that none of the material or equipment within the consignment is waste as defined by Article 3, point (1), of Directive 2008/98/EC; and

(d) 

appropriate protection against damage during transportation, loading and unloading, in particular through sufficient packaging and appropriate stacking of the load.

2. Point 1(a) and (b) and point 3 shall not apply where it is demonstrated by documentary proof that the shipment is taking place in the framework of a business-to-business transfer agreement and that:

(a) 

the used battery is sent back to the producer or a third party acting on its behalf for repair under warranty with the intention of re-use; or

(b) 

if the used battery is for professional use, it is sent to the producer or a third party acting on its behalf or a third-party facility in countries to which OECD Council Decision C(2001)107/Final on the Control of Transboundary Movements of Wastes Destined for Recovery Operations applies, for refurbishment or repair under a valid contract with the intention of re-use; or

(c) 

if the used battery is for professional use and is defective, it is sent to the producer or a third party acting on its behalf for root cause analysis under a valid contract, in cases where such an analysis can only be conducted by the producer or third parties acting on its behalf.

3. In order to demonstrate that the batteries being shipped constitute used batteries, rather than waste batteries, its holder shall carry out the following steps for testing and record-keeping:

Step 1: Testing
(a) 

the battery shall be tested for its state of health and the presence of hazardous substances shall be evaluated;

(b) 

the results of the evaluation and testing referred to in point (a) shall be recorded.

Step 2: Record
(a) 

the record shall be fixed securely but not permanently on either the used battery itself, if the used battery has not been packed, or on the packaging, so it can be read without removing the packaging;

(b) 

the record shall contain the following information:

— 
name of the battery or fraction thereof,
— 
identification number of the battery or fraction thereof, where applicable,
— 
year of production, if available,
— 
name and address of the company responsible for testing the state of health,
— 
types of tests performed for step 1,
— 
result of the tests performed for step 1, including the date of the tests.

4. In addition to the documentation required in points 1, 2 and 3, every load, for example shipping container or lorry, of used batteries shall be accompanied by:

(a) 

a relevant transport document; and

(b) 

a declaration of responsibility by the person liable.

5. In the absence of proof that an object is a used battery, and not a waste battery, in the form of the appropriate documentation required in points 1, 2, 3 and 4, and of appropriate protection against damage during transportation, loading and unloading, in particular through sufficient packaging and appropriate stacking of the load, which are the obligations of the holder that arranges the transport, the object shall be considered waste and it shall be presumed that the load comprises an illegal shipment. In such cases, the load shall be dealt with in accordance with Articles 24 and 25 of Regulation (EC) No 1013/2006.
ANNEX XV



ANNEX XV

CORRELATION TABLE



Directive 2006/66/EC

This Regulation

Article 1

Article 1

Article 1, first paragraph, point 1

Article 1(1)

Article 1, first paragraph, point 2

Article 1(1)

Article 1, second paragraph

—

Article 2

Article 1(3), (4) and (5)

Article 2(1)

Article 1(3) and (4)

Article 2(2)

Article 1(5)

Article 2(2), point (a)

Article 1(5), point (a)

Article 2(2), point (b)

Article 1(5), point (a)

Article 3

Article 3

Article 3, point 1

Article 3(1), point 1

Article 3, point 2

Article 3(1), point 2

Article 3, point 3

Article 3(1), point 9

Article 3, point 4

—

Article 3, point 5

Article 3(1), point 12

Article 3, point 6

Article 3(1), point 13

Article 3, point 7

Article 3(1), point 50

Article 3, point 8

Article 3(2), point (a)

Article 3, point 9

—

Article 3, point 10

Article 3(1), point 53

Article 3, point 11

Article 3(1), point 26

Article 3, point 12

Article 3(1), point 47

Article 3, point 13

Article 3(1), point 65

Article 3, point 14

Article 3(1), point 16

Article 3, point 15

Article 3(1), point 22

Article 3, point 16

—

Article 3, point 17

—

Article 4

Article 6

Article 4(1)

Annex I

Article 4(1), point (a)

Annex I, entry 1

Article 4(1), point (b)

Annex I, entry 2

Article 4(2)

—

Article 4(3)

—

Article 4(3), point (a)

—

Article 4(3), point (b)

—

Article 4(3), point (c)

—

Article 4(4)

—

Article 5

—

Article 6

Article 4

Article 6(1)

Article 4(1)

Article 6(2)

—

Article 7

Article 2

Article 8

Articles 59 to 62 and 64 to 67

Article 8(1)

Article 59

Article 8(1), first subparagraph, point (a)

Article 59(1), point (a) Article 59(1), point (b)

Article 8(1), first subparagraph, point (b)

Article 62

Article 8(1), first subparagraph, point (c)

Article 61(1) Article 62(1)

Article 8(1), first subparagraph, point (d)

Article 59(2), point (a)(ii) Article 61(1), point (c)

Article 8(1), second subparagraph

Article 59(5)

Article 8(2)

Article 59(1) and Article 59(2)

Article 8(2), point (a)

Article 59(1) and Article 59(2)

Article 8(2), point (b)

Article 59(2)

Article 8(2), point (c)

—

Article 8(3)

Article 61

Article 8(4)

Article 61

Article 9

—

Article 10

Articles 59, 60 and 69

Article 10(1)

—

Article 10(1), second subparagraph

Article 75(4)

Article 10(2)

Articles 59 and 60

Article 10(2), point (a)

—

Article 10(2), point (b)

Article 59(3) and Article 60(3)

Article 10(3)

Article 69(2) and Article 76(1), second subparagraph

Article 10(4)

—

Article 11

Article 11

Article 11, first paragraph

Article 11(1)

Article 11, second paragraph

Article 11(3)

Article 12

Article 70

Article 12(1)

Article 70(2)

Article 12(1), first subparagraph, point (a)

Article 59(1), point (f), Article 60(1), point (f), and Article 61(3), point (c)

Article 12(1), first subparagraph, point (b)

Article 71(1)

Article 12(1), second subparagraph

—

Article 12(1), third subparagraph

—

Article 12(2)

Article 71(4)

Article 12(3)

Article 70(3)

Article 12(4)

Article 71(2) and (3)

Article 12(5)

Article 75(5), point (c), and Article 76(1), point (d)

Article 12(6)

Article 71(4)

Article 13

—

Article 13(1)

—

Article 13(2)

—

Article 14

Article 70(1)

Article 15

Article 72

Article 15(1)

Article 72(1)

Article 15(2)

Article 72(3)

Article 15(3)

Article 72(4)

Article 16

Article 56

Article 16(1)

Article 56(1) and (4)

Article 16(1), point (a)

Article 56(4), point (a)

Article 16(1), point (b)

Article 56(4), point (a)

Article 16(2)

—

Article 16(3)

Article 56(1), point (c)

Article 16(4)

Article 74(5)

Article 16(5)

—

Article 16(6)

—

Article 17

Article 55

Article 18

Article 57(2), point (c)

Article 18(1)

—

Article 18(2)

—

Article 18(3)

—

Article 19

Article 59(1), Article 60(1), Article 61(1), Article 62 and Articles 64 to 67

Article 19(1)

Article 59(2), Article 60(2), Article 61(1) and Articles 62, 65, 66 and 67

Article 19(2)

Article 57(2), point (c)

Article 20

Article 74

Article 20(1)

Article 74(1)

Article 20(1), point (a)

Article 74(1), point (f)

Article 20(1), point (b)

Article 74(1), point (b)

Article 20(1), point (c)

Article 74(1), point (c)

Article 20(1), point (d)

Article 74(1), point (b)

Article 20(1), point (e)

Article 74(1), point (e)

Article 20(2)

Article 74

Article 20(3)

Article 74(4)

Article 21

Article 20 Article 13, Annex VI, Part A, B and C

Article 21(1)

Article 13(4)

Article 21(2)

Article 13(2)

Article 21(3)

Article 13(5)

Article 21(4)

Article 13(4)

Article 21(5)

Article 13(4)

Article 21(6)

—

Article 21(7)

—

Article 22a

—

Article 23

Article 94

Article 23(1)

Article 94(1)

Article 23(2)

Article 94(2)

Article 23(2), point (a)

—

Article 23(2), point (b)

Article 94(2), first subparagraph, point (e)

Article 23(2), point (c)

Article 71(5) and (6)

Article 23(3)

Article 94(2), second subparagraph

Article 23a

Article 89

Article 23a(1)

Article 89(1)

Article 23a(2)

Article 89(2)

Article 23a(3)

Article 89(3)

Article 23a(4)

Article 89(5)

Article 23a(5)

Article 89(6)

Article 24

Article 90

Article 24(1)

Article 90(1)

Article 24(2)

Article 90(3)

Article 24(2), second subparagraph

Article 90(3), second subparagraph

Article 25

Article 93

Article 26

—

Article 27

—

Article 28

Article 95

Article 29

Article 96

Article 30

—

Annex I

Annex XI

Annex II

Annex VI, Part B

Annex III

Annex XII

Annex III, Part A

Annex XII, Part A

Annex III, Part B

Annex XII, Part B

Annex IV

Article 55

1.1 Referenties

1.2 Geïdentificeerde eisen

1.3 Gerelateerde standaarden

2. Geïdentificeerde eisen

Eisen

3. Gerelateerde standaarden

Standaarden

Gekoppelde issues

Koppelingen
is related to Imported: Verordnung (EU) 2023/1542 über Batterien und Altbatterien (CELEX:02023R1542-20260813)